
Acrylic One (A1) base material
two-component material, consists of a mineral powder and a water based acrylic resin.

Acrylic One (A1) starter kit extended
7,5 kg Starter kit extended consists of a selection of the most popular additives and fillers.

Acrylic One (A1) triaxial fibre
Acrylic One (A1) triaxial fibre Triaxial fiber (Glass fiber) is used in combination with Acrylic One during lamination. In this way, Acrylic One objects can be made into molds, and covered with Acrylic One. Triaxial fiber ensures strengthening of Acrylic One objects. – Triaxial fiber is specially designed for Acrylic One – flexible, allowing easy drapable … Read More

Acrylic One (A1) basalt triaxial fibre
A1 Triaxial basalt fibre can be used as fibre reinforcement. Although the A1 Triaxial glass fibre causes little irrigation, it is a good alternative for people who are sensitive to working with glass
fibres.

Acrylic One (A1) Thixotrope A
Makes the product thicker to give it a gel structure.

Acrylic One (A1) Thixotrope B
Makes the product thicker to give it a paste structure.

Acrylic One (A1) sealer
Water based coating to protect the product against moisture and to give the product a weather resistant quality.

Acrylic One (A1) sealer
Water based coating to protect the product against moisture and to give the product a weather resistant quality.

Acrylic One (A1) accelerator
Shorten the processing time.

Acrylic One (A1) diluent
Reduces the viscosity of Acrylic One (A1).

Acrylic One (A1) pigments
Acrylic One (A1) pigments Acrylic One (A1) objects can be painted after it is ready, but can also be coloured beforehand by using Acrylic One (A1) pigments. The pigments are added into resin before mixing. The maximum quantity of pigment is 2% of the total weight or 6% of resin weight.

Acrylic One metal powders
There are various metal powders available which can be added to Acrylic One to achieve a metal effect. When you would like to achieve a rusted effect, use the iron power. Add an equal amount of iron powder as the amount of powder used to produce Acrylic One. When the applied layer had dried, it needs … Read More

Acrylic One (A1) Poraver filler 1-2 mm
lightweight filler

Acrylic One (A1) filler sand ORANGE
sand can be added up to 40% from the total weight of A1 base material

Acrylic One (A1) filler sand GREY
sand can be added up to 40% from the total weight of A1 base material

SLIP-LG 100 epoxy resin
Mixing ratio (by weight): 5: 2
Mixing ratio (by volume): 2: 1
Application time: 4 h (23 ° C)
Hardening time: 48 h

Monster Clay-modeling clay
Monster Clay Premium Grade Modeling Clay is a re-useable sulfur free, professional oil/wax based sculpting medium. Composed entirely of non-toxic, food grade components, Monster Clay has an ultra smooth formulation that features a low melt temperature and a low tack feel that will not stick to tools or fingers. Monster Clay has high plasticity and has … Read More

Monster Clay modeling clay GREY 2.27kg
Monster Clay is a premium class oil / wax based clay that does not contain sulphates and is reusable.

CAVEX CLEVER CAST alginate 500g
Cavex CleverCast is the ideal alginate for imprinting hands, feet, face or any other part of the body and is ideal for use with A1 (Acrylic One) and A1Creatives.
Flexible mixing ratio (alginate powder: water):
For small prints: 1:1 or 1:2
For larger prints: 1:3 or 1:4
Setting time: 3 to 5 minutes
Color: mint green
5% discount when ordering >5 units

Glorex modeling plaster cloth 2 m x 16 cm
Skin-friendly modeling plaster fabric.
Width: 16 cm
Length: 2 m

Glorex modeling plaster cloth 3 m x 8 cm
Skin-friendly modeling plaster fabric.
Width: 8 cm
Length: 3 m

Glorex modeling plaster cloth 5 m x 10 cm
Skin-friendly modeling plaster fabric.
Width: 10 cm
Length: 5 m

Acrylic One metal powders
There are various metal powders available which can be added to Acrylic One to achieve a metal effect. When you would like to achieve a rusted effect, use the iron power. Add an equal amount of iron powder as the amount of powder used to produce Acrylic One. When the applied layer had dried, it needs … Read More

Protoplast moldable plastic
You can heat and cool Protoplast as many times as you like.

Feather Lite Lightweight Urethane Resin
Mixing ratio (by weight): 1: 1
Mixing ratio (by volume): 1: 1
Hardness (Shore D): 58 D
Processing time: 8.5 min
Hardening time: 2 h

Tarbender High Gloss epoxy coating 1.28kg
Tarbender High Gloss epoxy coating and encapsulant
- UV resitant
- Optically clear
Mixing ratio (by weight): 100A:41B
Mixing ratio (by volume): 2A:1B
Hardness (Shore D): 75 D
Pot life: 45 min
Cure time: 16 h

XTC-3D epoxy resin 0.18kg
Epoxy coating self-levels and wets out uniformly without leaving brush strokes.
Mix Ratio (by volume): 2:1
Mix Ratio (by weight): 100:42
Shore Hardness (Shore D): 80 D
Working Time: 20 min
Tack Free Time: 4h (Thin Film Recoat Time 90 minutes)

EpoxAcast 690 Clear Casting Epoxy Resin 1.18kg
EpoxAcast™ 690 is a clear casting epoxy that is ideal for making clear jewelry/beads or replacement lenses for kit cars and other applications requiring a rigid, clear finished product.
Mixing ratio (by weight): 100A: 30B
Hardness (Shore D): 80 D
Curing time: 24 hours
Pot Life: 5 hours

Crystal Clear 202
Crystal Clear 202 fully transparent polyurethane resin for castings up to 2 cm in thickness.
Mixing ratio (by weight): 100A: 90B
Hardness (Shore D): 80 D
Working time: 9 min
Curing time: 90 min

Smooth-Cast 300 polyurethane resin 0.86kg
Smooth-cast 300 castings after hardening are durable, machinable and colorable.
Mixing ratio (by volume): 1: 1
Mixing ratio (by weight): 100: 90
Hardness (Shore D): 70 D
Processing time: 3 min
Curing time: 10 min

Smooth-Cast 305 polyurethane resin 0.86kg
Smooth-cast 305 castings after hardening are durable, machinable and colorable.
Mixing ratio (by volume): 1: 1
Mixing ratio (by weight): 100: 90
Hardness (Shore D): 70 D
Processing time: 7 min
Curing time: 30 min

Smooth-Cast 65D polyurethane 6.99kg
Smooth-cast 65D castings after hardening are durable, machinable and colorable.
Mixing ratio (by volume): 1: 1
Mixing ratio (by weight): 100: 90
Hardness (Shore D): 65 D
Processing time: 2,5 min
Curing time: 15 min

Smooth-Cast 326 plastic 0,86 kg
Smooth-cast 326 castings after hardening are durable, machinable and colorable.
Mixing ratio (by volume): 1: 1
Mixing ratio (by weight): 115A:100B
Hardness (Shore D): 72 D
Processing time: 9 min
Curing time: 60 min
Color: Clear Amber

Smooth-Cast ONYX (fast) 0,99kg
Features
Ultra-black and darker than competitive black resins.
Can be polished and buffed to a high gloss shine.
Higher heat resistance vs. competitive black resins.
Does not contain mercury.
Less expensive vs. other black resins.

Smooth-Cast ONYX (slow)
Features
Ultra-black and darker than competitive black resins.
Can be polished and buffed to a high gloss shine.
Higher heat resistance vs. competitive black resins.
Does not contain mercury.
Less expensive vs. other black resins.

VytaFlex™ urethane rubbers 0.91kg
VytaFlex™ mold rubbers work especially well for casting pigmented / colored concrete. Molds made with VytaFlex™ Series urethanes will render accurate and uniform colored castings.
VytaFlex® urethanes feature convenient one-to-one by volume mix ratios.

SORTA-Clear 18 silicone
Mix Ratio By Weight -100A:10B
Pot Life – 60 minutes
Cure Time – 24 hours
Shore Hardness – 18 A

Psycho Paint platīna silikona krāsas bāze
Measuring Is Done By Volume – The recommended mix ratio is 100 Parts A + 100 Part B + 200-500 Parts Solvent depending on your application (hand painting vs. airbrushing).
Adding Color To Psycho Paint – Silc Pig silicone pigments are compatible with Psycho Paint. There are several colors to choose from, and you can mix colors to create custom colors. The most accurate way to add pigment is by weight (using a gram scale). We recommend beginning by pre-mixing 2% pigment by weight to Part B and pre-mixing thoroughly. Do not exceed a 5% pigment load of the total weight (A+B). You can also use powdered cosmetic pigments to color Psycho Paint™, however a compatibility test is recommended.

NOVOCS Matte solvent 340g
Materials should be stored and used in a warm environment (73°F / 23°C). This material has a limited shelf life and should be used as soon as possible. Wear safety glasses, long sleeves and rubber gloves to minimize contamination risk.
Mix the A and B components of two component silicone sytems before adding NOVOCS. Add the desired proportion of NOVOCS solvent to create a thinner silicone mixture which can be brushed or airbrushed onto the surface of a cured silicone casting.
Example Recommended Ratios For Use:
- When adding to Psycho Paint, add between 200%-400% NOVOCS™ solvent by weight
- When adding to Sil-Poxy, add between 300%-500% NOVOCS™ solvent by weight

Cast Magic™ Powders
The set includes 10x40ml:
4 x glitter types
4 x metallic tones
2 x pearl tones

SO-Strong pigments
Pigments for tinting urethane rubbers, plastics, foams and epoxy systems.

Ignite fluorescent color pigments
When you add Ignite fluorescent color to a urethane material, more ultraviolet light from the cured material is visible to your eye vs. castings made with SO Strong™ colorants. The casting appears brighter in ambient light and appears to glow under ultraviolet light.

UVO Color Pigments
For maximum UV resistance, UVO™ pigment should be used with a UV-resistant material such as Crystal Clear™ plastics or Clear Flex™ rubbers.

Silc-Pig Silicone Pigments
The set contains nine different color pigments: blood colors, flesh colors, brown, red, black, green, blue, yellow, white.

ZA SFX 00-20 silicone
ZA SFX 00-20 silicone is a bicomponent (base and catalyst) addition RTV 2 silicone rubber that vulcanizes at room temperature.
Mixing ratio: 1:1
Final hardness: 23 sh00
Working timeat 23°C: 25 min
Setting time at 23°C: 70 min

ZA 10 ORANGE silcone
ZA 10 ORANGE silicone is a bicomponent (base and catalyst) addition RTV silicon rubber that vulcanizes at room temperature.
Mixing ratio: 1:1
Final hardness: 13 shA ± 2 shA
Setting time at 23°C: 90-120 min
Working time: 13-16 min
Colour: orange

SILSKIN 10 silicone
SILSKIN 10 silicone is a bicomponent (base and catalyst) addition RTV 2 silicone rubber that vulcanizes at room temperature.
Mixing ratio: 1:1
Final hardness: 10 ±2 shA
Setting time at 23°C: 30 min
Working time: 6-8 min

ZA 13 Mould WT 45 silicone
ZA 13 MOULD WT 45 is a bicomponent (base and catalyst) addition RTV 2 silicon rubber that vulcanizes at room temperature.
Mixing ratio: 1:1
Final hardness: 13 shA
Setting time at room temperature: 6-7 h

ZA 22 Mould silicone
ZA 22 MOULD is a bicomponent (base and catalyst) addition RTV silicon rubber that vulcanizes at room temperature.
Mixing ratio: 1:1
Final hardness: 22 shA
Setting time at 23°C: 1 h
Working time: 14-17 min
Color: BLUE or WHITE

ZA RTV 20-45 yellow silicone 25+25kg
ZA RTV 20-45 yellow silicone is a bicomponent (base and catalyst) addition RTV silicon rubber that vulcanizes at room temperature.
Mixing ratio: 1:1
Final hardness: 20 shA
Working time (at 23°C): 50 min
Setting time (at 23°C): 4 h
Color: YELLOW

ZA 22 Thixo Body Silicone
ZA 22 THIXO BODY is a bicomponent (base and catalyst) addition RTV 2 silicone rubber that vulcanizes at room temperature.
Mixing ratio: 1: 1
Final hardness of the template: 22 ShA
Development time: 6 min
Vulcanized color – skin tone

HT 24 Transparent silicone
HT 24 Transparent silicone is a bicomponent (base and catalyst) addition RTV 2 silicone rubber that vulcanizes at room
temperature.
Mixing ratio: 1:1
Shore A hardness after 24 hours: 24 shA
Working time at 23 °C: 20 min
Setting time at 23 °C: 3 h

HT 33 Transparent silicone
HT 33 TRANSPARENT is a bicomponent (base and catalyst) addition RTV 2 silicone rubber that vulcanizes at room temperature.
Mixing ratio: 1:1
Final hardness: 33 shA
Setting time at 23°C: 3h

ZA 32 LT Rosso silicone
ZA 32 LT Rosso is a bicomponent (base and catalyst) addition RTV silicon rubber that vulcanizes at room temperature.
Mixing ratio: 1:1
Color: reddish-brown
Hardness: 32 ShA
WT: 10 min
ST: 90 min

ZA 35 Mould silicone
ZA 35 MOULD is a bicomponent (base and catalyst) addition RTV silicon rubber that vulcanizes at room temperature.
Mixing ratio: 1:1
Final hardness: 35 shA
Setting time at 23°C: 1 h
Working time: 12-15 min
Colour: yellow

ZA RTV 20-45 YELLOW silicone
ZA RTV 20-45 YELLOW silicone is a bicomponent (base and catalyst) addition RTV silicon rubber that vulcanizes at room temperature.
Mixing ratio: 1:1
Final hardness: 20 shA
Setting time at 23°C: 4 h
Working time: 50 min
Colour: yellow

HT 45 Transparent silicone
HT 45 TRANSPARENT is a bicomponent (base and catalyst) addition RTV 2 silicone rubber that vulcanizes at room temperature.
Mixing ratio: 1:1
Final hardness: 45 shA
Setting time at 23°C: 2.5h

ZA 50 LT silicone
ZA 50 LT silicone is a bicomponent (base and catalyst) addition RTV silicon rubber that vulcanizes at room temperature. Mixing ratio: 1:1 Final hardness: 50 shA ± 3 shA Setting time at 23°C: 180 min Working time: 15-20 min Colour: blue.

ZA 35-15 GLASS 2KG
Silicone rubber for special effects such as ice, glass, water.
Cures at room temperature (RTV2).
Mixing ratio: 1: 1
Final hardness of the mold: 20 ShA

Zhermack alginate
Body casting Alginate Alginate information – contains 70% water, you ONLY can realize ,a SINGLE COPY as your mould will start to shrink. The main materials you can cast inside are gypsum, silicone and A1. Zhermack algināts AL-MT datu lapa (EN) Zhermack AL-PR datu lapa (EN)

Set chamber 4.2l + pump 51l/min
Kit Contents:
vacuum pump VP1RS-0.5 (51l/min (1.8CFM) and ultimate vacuum 5Pa (37microns))
oil needed for the first start
vacuum chamber VC1621S (4.2l and internal dimensions are: diameter 16cm to 21cm in height).
reinforced pneumatic hose with a fitting enabling connection to a vacuum pump (internal diameter of 8 mm and a length of 1.5 m).
instruction manual

Set chamber 12.5l + pump 71l/min
Kit Contents:
- vacuum pump 71l/min(2.5CFM);
- oil needed for the first start
- vacuum chamber 12.5l (d=25cm; h=23cm)
- reinforced pneumatic hose with a fitting enabling connection to a vacuum pump
Warning. Chambers with polycarbonate lid are not designed for wood stabilization or to work with alcohol, ethanol, acetone and monomers or polymers based on acrylic. For these purposes, we recommend using chambers with tempered glass lid, which we also have in our offer.

Vacuum chamber 4.2l
Kit Contents:
Aluminum tank 4,2l (210mm x 160mm)
Leak free air manifold with glycerin gauge and air filter
Reinforced pneumatic hose with a fitting enabling connection to a vacuum pump (internal diameter of 8 mm and a length of 1.5 m)

Vacuum chamber 12.5l
Kit Contents:
Aluminum tank 12.5l (250mm x 230mm)
Industrial vulcanized 100% silicone (no glue) gasket with a hardness of 60°ShA and temperatue resistance of 190°C
Leak free air manifold with glycerin gauge and air filter
Reinforced pneumatic hose with a fitting enabling connection to a vacuum pump (internal diameter of 8 mm and a length of 1.5 m)

Pressure chamber 8l
Pressure chamber 8l
- steel chamber 8l (d = 21cm; h = 23cm) with silicone seal and thick steel lid;
- glycerin meter and air filter.
Air compressor not included!

Vacuum pump 51l/min
Kit Contents:
- vacuum pump 51l/min(1.8CFM);
- oil needed for the first start

Vacuum pump 71l/min
Vacuum pump 71l/min:
- vacuum pump 71l/min(2,5CFM);
- oil needed for the first start,

Vacuum pump oil
Shell oil is designed for use in rotary vacuum pumps.
Oil is formulated from selected premium performance, highly refined mineral oils. This provides the low vapour pressure and high performance, desired for the effective lubriaction of rotary vacuum pumps.

ACMOS 82-2405 release agent
Acmos 82-2405 – Removable universal release agent/ wax based / aerosol spraycan

Ease Release™ 2831,Release Agent 0.36kg
Ease Release™ 2831, Wax-Based Non-Silicone Release Agent

ACMOS 70-2406 release agent
Silicone-based release agent

Ease Release 200
Features:
Easy to apply
Fast drying
Effective over a broad temperature range from 70°F to 500°F
Excellent release
Precise duplication of mold details
Less rejects, faster production Matte finish
Ordering at least 3 units – 5% discount.